Accueil
launch x431
Launch X431 PAD V ECU Online Programming Car Diagnostic Tools

Launch X431 PAD V ECU Online Programming Car Diagnostic Tools

4.5 (347) · € 1225.00 · En Stock

Launch X-431 PAD V OE-Level All System Automotive Diagnostic Scanner with 50+ Reset Service , helping customers to achieve multi-function diagnosis to the greatest extent in the same device.
Launch X-431 PAD V is the high-end diagnostic equipment newly launched by LAUNCH, integrating the LAUNCH excellent diagnostic technology and made many improvements and innovations. It has deeply optimized the system layer, greatly improved the system response speed, and optimized the user experience.LAUNCH X431 PAD V Online Programming 1. More safty during programming , even though you failed during programming , x431 pad v can allow you program again , will not break the ECU. 2. X431 PAD V supports programming and coding, which is to write the relevant control information of the software into the automotive computer's programmable EPROM or FLASH by making use of the electronic communication transmission technology. 3. X431 PAD V Support intelligent recognition of programming files, convenient and quick operation.Support for Mercedes-Benz, for Benz New Energy, for BMW, for BMW New Energy, for GM, General New Energy, for Ford,Ford New Energy, for Volkswagen, for Volkswagen New Energy, for Audi, for Audi New Energy, for Land Rover, for Nissan,Skoda, for Seat, for Mazda and other models Programming function. Active Test (Bi-directional Control)Actuate solenoids and actuators for active testing, send commands to systems/components to test their working status, without using the vehicle controls.ECU Coding (Online Coding)Match, learn, or code the newly replaced ECU; Customize your car, unfold the hidden features, or disable the annoying functions; Reprograms the adaptive data for certain components after repairs or replacements.Launch X-431 PAD V 30+ Special functions:1. Oil Reset ServiceThis function allows you to perform reset for the engine oil life system, which calculates an optimal oil life change interval depending on the vehicle driving conditions and climate. 2. Electronic Parking Brake ResetIf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.3. Steering Angle CalibrationTo reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle.4. ABS BleedingThis function allows you to perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS).5. Tire Pressure Monitor System ResetThis function allows you to quickly look up the tire sensor IDs from the vehicle’s ECU, as well as to perform TPMS replacement and sensor test.6.Gear LearningThe crankshaft position sensor learns crankshaft tooth machining tolerance and saves to the computer to more accurately diagnose engine misfires. If tooth learning is not performed for a car equipped with Delphi engine, the MIL turns on after the engine is started. The diagnostic device detects the DTC P1336 'tooth not learned'. In this case, you must use the diagnostic device to perform tooth learning for the car. After tooth learning is successful, the MIL turns off.7. IMMO Service8. Injector Coding9.Battery Maintenance System ResetThis function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.10.DPF RegenerationDPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.11. Electronic Throttle Position ResetThis function enables you to make initial settings to throttle actuators and returns the “learned” values stored on ECU to the default state. Doing so can accurately control the actions of regulating throttle (or idle engine) to adjust the amount of air intake.12. Gearbox Matchingif vehicle won’t start or “Check Engine” light is illuminated. Check car’s fuel system regularly ensures the best performance of your car with the lowest emissions.13. AFS Reset14.Sunroof Initialization15 Suspension Calibration16.EGR Adaption17.Seats Calibration18. Tyre ResetThis function is used to set the size parameters of the modified or replaced tire.19.Coolant BleedUse this function to activate the electronic water pump before venting the cooling system.20.AdBlue ResetAfter the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.21.NOx Sensor ResetNOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.And moreLaunch X431 PAD V vs Launch X431 PAD III:Launch X-431 PAD V Supported Languages:English, Italian, German, Japanese, Russian, French, Spanish, Portuguese, Polish, Turkey, Dutch, Greek,Hungarian, Arabic, Denish, Korean, Farsi, Romanian, Serbian, Finish, Swedish, Czech.Launch X-431 PAD V Update & Warranty:One Year Free Update & 5 Years WarrantyLAUNCH X431 PAD V Tablet Parameter: Operating System: Android 9.0 CPU: 8-core Processor,2.OGHz Battery: 7000mh, rechargeable polymer lithium battery Extension memory card: 64G（Can up to 128GB ） Storage capacity: 4G LCD: 10.1 inch LCD resolution: 1920*1200 Touch screen: IPD touch screen Cameras: 8MP front-facing camera+ 13MPrear-facing camera Wi-Fi: 2.4G/5GHz Dual Frequency Connectivity: Wi-Fi (802.11 blg/n/ac)/Universal serial BUS Ports (1 x Type-C +1xType-A) Sensor: Gravity Accelerometer/3-Axis Acceleration Sensor Working temperature: 0℃~50℃ Storage temperature: -20℃~70℃ Smartbox VCI Parameter: Working Voltage: DC 9v ~36V RAM: 256MB ROM: 8GB USB: Type Bx 1 Wi-Fi: 2.4G/5GHz Dual Frequency Power: ≤6.6W Working Temp.: o℃ ~ 50℃ Launch X-431 PAD V Support Vehicles:Launch X431 Pad V Package List:1 x X-431 PAD V main unit1 x Smartbox 3.0 diagnostic connector1 x X-431 PAD V Docking Station1 x Cigarette lighter cable1 x USB cable1 x Power adaptor1 x Battery clamps cable1 x OBD II extension cable1 x OBD I Adaptor1 x Password envelope1 x Nissan-14+161 x Mitsubishi Hyundai-12+161 x Daihatsu-41 x Benz-141 x Fiat-31 x Suzuki-31 x Audi-41 x GAZ1 x SG-141 x UN Iversal-3

Launch ECU Programming Model Launch Pad VII 7 Auto Diagnostic Scanner Vs Launch Pad V5 X431 PRO V Plus4.0 - China Launch X431 Padvii, Launch X431 Pad 7